Metal roofing
Architectural shingles
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Styles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Metal Roof Installation Cost in Burbank?
Metal roof installation in Burbank, CA typically costs $18,500 to $42,000 for a full tear-off and replacement on a standard single-family home, which works out to roughly $12 to $26 per square foot installed depending on panel type, roof complexity, and whether you need new underlayment and structural prep. A basic exposed-fastener panel system on a simple ranch roof can land near the low end, while a standing-seam roof with hidden fasteners on a steep, multi-plane Burbank hillside home pushes toward the top. Most Burbank homeowners we work with spend in the $24,000 to $32,000 range.
Key Takeaways
- Burbank metal roof installs run $18,500 to $42,000 for most homes; standing seam costs more than exposed-fastener panels.
- Expect to spend $12 to $26 per square foot installed, all-in.
- Metal typically lasts 40 to 70 years, often two to three times longer than asphalt shingles.
- What drives the price up most in Burbank: hillside access, steep pitch, and fire-rated requirements.
- We give free, no-pressure estimates, and we’ll tell you if a repair gets you through another few years instead.
Metal Roof Installation Cost Breakdown (2026)
Here’s how the numbers break down line by line for a typical Burbank home in the 1,500 to 2,000 square foot range. Actual figures shift with roof size, pitch, and material, but this gives you a realistic budget to work from.
| Line Item | Typical Cost Range |
|---|---|
| Tear-off and disposal of old roofing | $2,000 – $4,500 |
| Structural inspection and deck repair (if needed) | $0 – $3,800 |
| Underlayment and waterproofing membrane | $1,200 – $3,000 |
| Exposed-fastener metal panels (materials) | $4.50 – $8 per sq ft |
| Standing-seam metal panels (materials) | $9 – $16 per sq ft |
| Labor and installation | $5 – $11 per sq ft |
| Flashing, trim, ridge caps, and vents | $800 – $2,500 |
| Permit and inspection fees (Burbank) | $400 – $1,100 |
Add the pieces up and you land in that $18,500 to $42,000 window for most homes. What pushes a job toward the high end? Standing seam over exposed-fastener, a steep pitch over a low-slope roof, and a complex roof with lots of valleys, dormers, and penetrations. A simple gable roof on a flat lot is the cheapest to install because there’s less cutting, less flashing, and fewer places for panels to slow the crew down. A hillside house in the Burbank foothills is the opposite: harder access, more safety rigging, and more custom trim work.
Material brand matters too. Because we install across seven major manufacturer lines (GAF, CertainTeed, Owens Corning, IKO, Atlas, Tamko, and Boral), we can match panel type and warranty tier to your budget instead of steering you to whatever a single-brand shop happens to stock. That flexibility usually saves a few thousand dollars over a contractor locked into one product line.
What Affects Metal Roof Installation Pricing in Burbank
Burbank is not a flat, easy-roof town. Here’s what moves the number up or down on a real job here.
- Roof pitch and complexity. Burbank has a lot of hillside homes north of Glenoaks and up toward the Verdugo foothills, and steeper pitches mean more safety rigging, slower panel handling, and more cutting. A steep, cut-up roof can add $4,000 to $8,000 over a simple one.
- Fire-rated metal requirements. Much of Burbank sits in or near high fire hazard zones (the hillside areas especially), and metal is one of the most fire-resistant roof choices you can make. If your home is in a WUI (wildland-urban interface) zone, the metal you choose may need specific fire ratings, and that can nudge material cost up slightly. It’s also a big part of why metal appeals here.
- Old roof condition. If the existing roof has rot, soft decking, or failed flashing under it, we have to address that before panels go on. We inspect first and show you exactly what we find, so you’re never paying for deck repairs you don’t actually need.
- Access and staging. Narrow Burbank streets, steep driveways, and tight lots in neighborhoods like Magnolia Park and the Rancho district can slow down staging, which adds a bit of labor.
- Panel type. Standing seam (hidden fasteners, cleaner look, better long-term performance) costs noticeably more than exposed-fastener panels. Both are real options; the right one depends on your roof and budget.
- Color and finish. Premium finishes and certain colors (especially darker, high-end finishes) cost more and may have longer lead times, while standard colors keep pricing closer to the low end. We’ll show you the trade-offs.
How to Save on Metal Roof Installation
Metal is a bigger upfront spend than asphalt shingles, but there are honest ways to keep the Burbank number down without cutting corners.
- Get the inspection first, not a replacement pitch. A good inspector tells you whether your current roof has years left. We investigate before we recommend. If a targeted repair buys you three more years, we’ll say so. (You can read more about how we approach that on our home page.)
- Choose exposed-fastener panels if the look works for you. They cost less than standing seam and perform well. If curb appeal isn’t the deciding factor, this is often the single biggest saver.
- Bundle timing. Off-season scheduling and combining the roof with any needed deck or flashing work into one job usually beats piecemeal pricing.
- Ask about warranty tiers. Multi-brand access means you can weigh coverage options against price. We’ll lay them out side by side.
- Compare per-square-foot, not lump sum. It’s the fairest way to compare bids and spot a lowball that’s missing underlayment or flashing.
Every estimate we give is free and upfront. Call (866) 705-2978 and we’ll walk your roof and talk real numbers, including whether metal is even the right call for your house.
Why Metal Roofing Costs What It Does
It helps to understand where the money goes. Metal roofs cost more than asphalt because the material itself is pricier, the installation is more skilled, and the lifespan is dramatically longer. A quality metal roof can last 40 to 70 years, often outlasting the homeowner’s stay in the house. When you spread a $28,000 metal roof over 50 years of service, the per-year cost is competitive with replacing asphalt shingles two or three times over the same period.
Burbank’s climate actually plays to metal’s strengths: intense sun, dry summers, and the occasional winter rain, plus the wildfire exposure in the hills. Metal reflects heat, resists fire, and sheds water cleanly. That’s why we see real demand for it here, and why the upfront math deserves a fair look rather than a quick “too expensive.”
Repair or Replace? A Note Before You Commit
Not everyone who calls about a metal roof needs one. Sometimes a leak, missing shingles, or storm damage can be fixed and you can keep the roof you have for years. Our name leads with repair for a reason: we investigate before we recommend replacement. If a targeted fix is the smarter move, we’ll tell you plainly, even if it means a smaller job for us. If it’s genuinely time for a new roof, we’ll show you why with photos and specifics, not pressure. That’s the approach behind metal roof installation in Burbank, and it’s the same on every job.
Frequently Asked Questions About Metal Roof Cost in Burbank
How much does metal roof installation cost in Burbank per square foot?
Most Burbank metal roof installs run $12 to $26 per square foot installed, all-in. That includes tear-off, underlayment, panels, and labor. A simple roof on a flat lot sits near $12; a steep hillside roof with standing seam and custom trim climbs toward $26. Call (866) 705-2978 for a number specific to your roof.
Is a metal roof cheaper than asphalt shingles in Burbank?
No. Metal costs more upfront, typically $18,500 to $42,000 versus several thousand for asphalt on the same home. But metal lasts two to three times longer and handles Burbank’s sun and fire exposure better. Over a 40 to 70 year lifespan, the per-year cost often comes out competitive. Call (866) 705-2978 and we’ll run the honest comparison for your house.
Do I need a permit for a metal roof in Burbank?
Yes, a roof replacement in Burbank typically requires a permit and inspection, and permit fees usually run $400 to $1,100 depending on scope. We handle the permitting as part of the job so you’re not chasing paperwork. Call (866) 705-2978 with questions about your project.
How long does metal roof installation take in Burbank?
Most residential metal roofs take three to seven days once materials are on-site, with larger or more complex roofs running longer. Lead times on materials, especially certain colors and standing seam, can add a few weeks before work starts. We’ll give you a realistic timeline in your estimate. Call (866) 705-2978 to schedule.
Is it worth it to replace an old roof with metal in Burbank?
Often, yes, especially on hillside homes in higher fire-risk areas where metal’s fire resistance matters, and where you plan to stay long enough to enjoy the long lifespan. But if your current roof has years left, a repair may serve you better. We investigate before we recommend. Call (866) 705-2978 for a free inspection and estimate.
Get a Free Metal Roof Estimate in Burbank
If you’ve been putting off a roof decision because you don’t know what it’ll cost, start with a real number. Marquis Roof Repair handles the full roof lifecycle, from inspection through repair to installation, and we install across seven manufacturer lines so the right material fits your roof and budget instead of someone’s stock. We investigate before we recommend, and every estimate is free and upfront. Call (866) 705-2978 today to schedule your estimate and get clear pricing for your Burbank home.
Pricing reflects the Burbank market as of 2026. Marquis Roof Repair offers free estimates. Call (866) 705-2978.
What Our Customers Say
"Tile roof, three cracked tiles and a slipped one. Matched the tile, no color mismatch, and it took him half a day."
— Grace Lin"Leak over the kitchen turned out to be a cracked boot around a vent pipe, not the roof itself. He showed me the photo from up there and replaced the boot for a couple hundred dollars. The company before him had quoted a full tear off."
— Doug Mercer"Roof is solid and the price was competitive. The job ran a day over because of weather, which is nobody's fault, but I would have liked a call about it rather than noticing the crew hadn't shown up."
— Maurice Ellison