Architectural shingles
Metal roofing
Tile roofing
GAF
Owens Corning
Flat & low-slopeFree roof inspection with deck photos before we talk money - GAF and Owens Corning certified installation
Fast, Reliable Roof Replacement Across Culver City
Roof replacement in Culver City typically runs $11,500 – $24,000 for a full tear-off on a standard bungalow, with architectural shingles landing around $14,500 – $19,000 and flat or low-slope membrane work between $9,800 and $16,200. Most tear-offs we schedule in Culver City take 3 to 5 working days once materials are staged. If you’re looking at a roof that’s been patched more than twice or you’re planning a second-story addition, call (866) 705-2978 and we’ll give you a straight read on what’s actually under the shingles before you commit to anything.
We work across 90230, 90231, 90232, and 90233, and we know the housing stock here well enough to expect the unexpected. Culver City roofs are rarely simple. A bungalow on a Carlson Park street might look like a standard tear-off from the curb, but what’s underneath often changes the whole scope once we open it up.
Why Marquis Roof Repair Is Culver City’s Preferred Roof Replacement Company
The reason homeowners in neighborhoods like Sunkist Park and Blair Hills call us back, and refer us to neighbors, has less to do with marketing and more to do with what happens when the roof comes off. In Culver City, the question is never just “how much for shingles.” It’s what we find underneath. Our crew has pulled original 1940s tar-and-gravel built-up roofs out from under later shingle overlays more times than we can count, and that experience changes how we quote, how we schedule, and how we protect the deck once it’s exposed.
Ron Thibodeau runs our crews with a simple expectation: open the roof before making promises, and never let a homeowner pay for a replacement they don’t actually need. That discipline shows up in how we handle Culver City’s older bungalows, where the decision to repair versus replace is often genuinely close. We’d rather tell you the roof has five more years than sell you a tear-off early. Homeowners remember that. It’s why our Culver City work keeps coming through referrals rather than ad spend.
We carry seven manufacturer lines, including IKO, Atlas, Tamko, and Boral, which means the material recommendation we make for your roof is based on your roofline, your low-slope sections, and your exposure to the marine layer, not on whatever single brand we happen to stock. For a city where one block of gable bungalows sits next to a block of mid-century low-slope tracts, that kind of portfolio matters.
Styles & brands we work with
Roof Installation in Culver City
Roof Installation in Culver City means something different than it does inland. Here, you’re rarely putting a roof on a clean, new deck. You’re often replacing a layered system on a 1940s or 1950s bungalow, or you’re tying new roof structure into an existing low-slope section when a second story goes on. The work here involves stripping old layers, evaluating the deck, replacing rotted sheathing, and then installing the right system for the pitch, the exposure, and the layering that already exists.
A full roof installation on a Culver City home generally runs $13,000 – $22,500 depending on whether we’re dealing with a straightforward gable or a mixed-pitch roof with flat sections. The low-slope portions are where costs concentrate: membrane work, tapered insulation, and drainage correction all add labor and material that a simple shingle quote never includes.
Working With Existing Roof Layers
Culver City’s older bungalows frequently have a shingle overlay sitting on top of the original built-up roof. That means a roof installation here often starts with removing two roof systems, not one. When we strip those layers, we’re also checking the deck for moisture trapped between them, which is where rot hides and where a cheap inland contractor’s quote falls apart.
Low-Slope and Flat Sections
Many Culver City homes, including mid-century tracts around Fox Hills, have flat or low-slope sections that need membrane rather than shingles. We install modified bitumen and single-ply systems on those sections and tie them correctly into the adjacent pitched roof valleys. Done wrong, those transitions leak within a season.
Roof Replacement Contractor in Culver City
A Roof Replacement Contractor in Culver City has to understand the city’s specific collision of old bungalow stock, mid-century flat roofs, and aggressive modern infill. The streamlined permitting and the sheer number of second-story additions and rooftop solar installations around downtown and the Fox Hills area mean we’re as often replacing a roof to support new construction as we are replacing one that’s simply failed. The scope here includes full tear-off, deck replacement, and installation matched to what the roof will carry after the remodel.
Expect a full replacement to run $11,500 – $24,000 in Culver City. The higher end reflects homes with multiple low-slope sections, hidden second roof systems, or decking that needs substantial replacement once the layers come off. The lower end is a simple gable with good decking and a clean removal.
Tear-Off and Decking Replacement
In Culver City, we never lay new shingles over an old roof. The moisture trapped between layers in this marine-layer climate rots decking faster than almost anything else. We strip to the deck, inspect every sheet, and replace anything that’s delaminating or soft. On bungalows with the original tar-and-gravel roof still underneath, that deck work is where the real cost, and the real protection, lives.
Replacement for Additions and Solar
When you’re building up or adding rooftop solar, the roof replacement has to be done in the right order. We coordinate with your general contractor or solar installer so the roof is stripped, re-decked, and membrane-installed before any new framing or racking goes on. It’s the difference between a roof that’s ready for the next thirty years and one that gets opened up again in two.
Trusted Brands We Service in Culver City
We’re authorized to install from seven manufacturers, including IKO, Atlas, Tamko, and Boral. That’s not a marketing point so much as a practical one: the right material for a Culver City roof depends on whether we’re dealing with a steep gable bungalow off Overland Avenue, a low-slope mid-century tract in Sunkist Park, or a flat-roofed commercial-to-residential conversion near downtown. Single-brand roofers have to make one material work for all of those. We don’t have that constraint. We specify what your roof, your pitch, and your exposure actually call for, and we can source it without making you wait on a special order.
Common Roof Replacement Problems We See in Culver City Homes
- Hidden second roof systems. Shingle overlays laid over the original 1940s – 50s built-up flat roofs trap moisture between layers. By the time we strip both, the decking is often rotted in ways no attic inspection could have caught.
- Marine-layer condensation. Poorly ventilated low-slope roofs collect condensation from the nightly marine layer. Cheap fasteners rust, flashing corrodes, and the membrane fails long before its rated lifespan.
- Santa Ana wind damage at gable edges. Under-specified drip edge and valley flashing on bungalow gables get pried loose during Santa Ana events, especially where fascia was never replaced. We see this concentrated in the older Carlson Park and Blair Hills-era tracts.
- Flat roof failures on postwar stock. The original tar-and-gravel roofs on 1940s and 1950s homes were built for a different climate expectation. Decades of intense UV off the basin, plus the marine layer, have pushed many of them past what patching can manage.
See the difference
Before
After
Before
After
Before
AfterPricing for Roof Replacement in Culver City, CA
A standard architectural shingle roof on a Culver City bungalow runs $14,500 – $19,000. If you have a flat or low-slope section, expect that portion to add $9,800 – $16,200 depending on square footage and whether we need to correct drainage. Full tear-offs with substantial deck replacement land between $18,000 and $24,000. The biggest variable in Culver City is what’s under the current roof: a single layer strips clean and costs less; a shingle-over-tar-and-gravel built-up roof doubles the removal labor and often doubles the deck replacement. A coastal-spec installation with stainless fasteners and marine-grade flashing adds roughly 6 – 9% over an inland-spec job, and it’s the version we recommend here. Call (866) 705-2978 for a free estimate, and we’ll walk the roof with you before putting any numbers on paper.
We Also Serve Cities Near Culver City
Beyond Culver City, we regularly handle full Roof Replacement work in Ladera Heights, Century City, Beverly Hills, and View Park-Windsor Hills. If you’re in one of those areas and dealing with the same old-roof-plus-marine-layer conditions, the same crew and the same seven-brand material access apply. Call us and we’ll schedule a look.
Serving Culver City, CA — Our Local Coverage Area
We’re based in the Culver City area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Roof Replacement in Culver City
Because the original 1940s and 1950s built-up tar-and-gravel flat roofs on these bungalows were never torn off when later owners wanted the look of shingles. A contractor laid shingles directly over the old flat roof, which trapped moisture between the two systems. We find this routinely in Carlson Park, Sunkist Park, and the older tracts around downtown. It means your replacement quote needs to account for removing two roofs, not one. Call (866) 705-2978 and we’ll tell you whether your house has this condition before you sign anything.
Yes, but not the way most people think. The breeze itself doesn’t damage the roof. The marine-layer moisture it carries does. Nightly condensation settles under low-slope roofs, rusts cheap fasteners, corrodes flashing, and shortens membrane life. Combine that with the basin’s intense UV, and a roof specified for inland conditions fails years earlier here. We specify stainless fasteners and marine-grade flashing on Culver City replacements for exactly this reason.
The difference is in the fasteners, flashing, and edge details. A coastal-spec Culver City replacement uses stainless or hot-dip galvanized fasteners, marine-grade flashing at valleys and penetrations, and sealed joints at all transitions. It costs about 6 – 9% more than an inland-spec job. An inland contractor quoting Culver City work often prices the inland spec. It looks identical for the first few years, and then the fasteners rust and the flashing corrodes. We’ve replaced roofs where the cheap inland spec was only eight years old. Call (866) 705-2978 for a bid that specifies what’s actually on the roof.
Look at the line items, not the total. Does each bid specify the number of layers being removed? Does it include deck replacement by the sheet, with a unit price? Does it name the fastener and flashing spec, and does it match the coastal conditions in Culver City? Does it address the low-slope sections separately from the pitched sections? If one bid doesn’t mention the low-slope portion at all, that contractor hasn’t looked at your roof. We give written, line-item quotes so you can compare them directly. Call (866) 705-2978 for yours.
For most Culver City gable bungalows, yes, an architectural shingle from IKO, Atlas, or Tamko is sufficient, provided the drip edge and valley flashing are specified correctly and installed with the right fasteners. The wind itself is not the primary problem. It’s what a Santa Ana event does to under-specified edge metal on an older bungalow. A properly detailed architectural shingle roof with marine-grade edge metal handles our wind pattern without issue. We’ll tell you honestly if your roof needs something different.
Call Marquis Roof Repair for Roof Replacement in Culver City
If you’re in Culver City and your roof is aging, leaking, or about to carry a second story or a solar array, call (866) 705-2978. We’ll inspect what’s actually on the roof, tell you what’s underneath if we can see it, and give you a written quote that covers the full scope. No pressure to replace if you don’t need it. Ron Thibodeau and our crew work to the Marquis standard, from first inspection to final shingle. Estimates are free.
Written by Ron Thibodeau, Owner at Marquis Roof Repair, serving Culver City and the surrounding basin.